No shipping required, software license is emailed within minutes.
Please note software is not eligible for returns or cancellation once purchased.
Ask us about compatibility & system requirements before purchasing.
Manic Compressor was designed from the beginning to be more than just a compressor. It was designed to unleash the power of parallel compression without requiring complex routing in your DAW.
Even with 6 different compressor modes and a comprehensive parallel routing setup, Manic Compressor uses an intuitive interface to get you way more power from your compressor than you’ve ever had before.
Manic Compressor—Unique Features
Six compressor models designed with parallel compression in mind
Instantly switch between models with settings retained
Separate faders for wet, dry, and master levels
Wet/Dry Mix button lets wet and dry faders act as mix knobs instead of separate faders
Three-position “Beef” switch with Thin, Neutral, and Thick settings that change the compressor’s response to an input signal
Variable knee for subtle compression before the threshold is crossed
“Loud Relief” relaxes response to transients during heavy compression of loud program material, allowing a natural dynamic response with extreme settings
Tone Signal Application selects which part of your signal chain the Tone EQ affects (wet or dry).
Mid/Side panner that can be used as a simple stereo widener or fix any mid/side level discrepancies in Mid or Side mode
Manic Compressor—Just the Facts
Standard compression controls
Selectable Dual Mono, Stereo, Mid, and Side operation
Drive controls input gain and adds analog saturation as gain increases
Selectable internal or external sidechain
Sidechain input listen
Pre/Post sets tone equalizer before or after the compressor
A/B bank lets you compare settings
Manic Compressor is built for parallel compression right from the drawing board. It comprises six unique compressor models, each optimized for the response you want from bus compression, plus separate faders for compressed, uncompressed, and master levels—offering true parallel compression in a single plug-in. However, if you want subtle compression with natural sound, you can combine the Wet and Dry faders to function like a mix knob.
The Power of Six
With Manic Compressor, you can switch between its six compressors instantly without any change in settings, so you can hear the tonal effect and impact of each in action without losing perspective. Plus, since compression is treated more and more as a creative effect, Manic Compressor is built for abuse, enabling you to go to extremes and achieve unique, musically useful sounds that go beyond the limits (so to speak) of mere level control. One such effect is the Tone EQ in a parallel compression setup.
Built-in Tone and Sidechain EQ
In standard parallel compression schemes, EQ is used to boost or cut various frequencies for pre- or post-compression effects. Ahead of the compressor, EQ can tame sounds going into the compressor, such as cymbals from being too harsh, or, it can prevent low frequencies from pulling down the mix.
Used after the compressor, EQ can emphasize lost frequencies or tame those that the compressor over-emphasizes. This involves a lot of extra steps, even in software. Either way, this approach is more utilitarian than creative.
Manic Compressor gives you both practical and creative EQing. It hosts two EQ sections, both with their own preset manager, for the “all-in-one” functionality you’ve come to expect from Boz Digital. The Sidechain EQ, which is not audible, affects the signal going into the detector, determining how it reacts to program material by emphasizing or de-emphasizing selected frequencies. Additionally, the Sidechain input, selectable between internal and external sources, can be monitored in isolation for tweaking purposes.
The second EQ section is the Tone EQ, which does affect the audio output and gives you creative license to go wild if you want to. This EQ is designed to give you control over the frequency bands mainly associated with parallel compression.
However, it’s not simply for low- and high-end boost. It follows its own set of rules. You can use extreme settings and blend them in with the dry signal for some truly unique sounds, unattainable by standard compressors and EQs.
Bringing Transients into Sharp Relief
You know you have a great piece of kit when you can crank knobs all the way up and still get a good sound, or an unexpectedly great sound, which is what Manic Compressor is built for—so let’s make some mistakes—that’s what it’s all about. The last “mistake” that spawned a unique compression effect was the “all button mode,” which is so 50 years ago. Among Manic Compressor’s innovative features is its Loud Relief control, which lets you apply extreme amounts of compression while relaxing the compressor’s grip on loud transients for a more natural sound.
With Loud Relief, Manic Compressor lets you visit sonic mayhem on an unsuspecting populace, crushing tracks under your merciless boot heels, and then ease off with Loud Relief, which softens the compression artifacts even under super heavy load.
_________________________________________ System Requirements
M1 Mac Users: This plugin is not yet compiled to work natively on M1 Macs. We are currently in the process of rewriting it so that it will, but it will take some time. In the meantime, it should work under rosetta on M1 Macs.
Platform: Mac, PC
Bit Depth: 32-bit, 64-bit
Format: AAX, VST2, VST3, AU
Hardware Required - Mac: Intel Core 2 Duo or higher, 4GB RAM minimum
Hardware Required - PC: Intel Core 2 Duo / AMD Athlon 64 X2 or higher, 4GB RAM minimum